Why House Paint Fails - Exterior Surfaces
 
 
House paint can fail prematurely and the following identifies some reasons and remedies.
 
Wood was wet when it was painted
 
If only the surface of the wood is wet, then only 1 sunny day is usually needed for drying prior to painting. If the wood is saturated, several sunny or windy days are necessary for drying prior to painting.
 
Unfinished siding was exposed to several weeks of sunlight before painting
 
Sunlight degrades the unfinished wood surface, thus it will never hold paint as well as fresh wood.
If the unfinished wood was ex- posed more than 3 to 4 weeks, lightly sand or power wash the surface to remove the thin layer of degraded wood before applying paint.
 
The temperature was too cold when the wood was painted
 
Oil-based paints should be applied when the temperature is at least 10 degree C; for latex paints, the temperature should be at least 10 degree C. Conditions should remain above these temperatures for 24 hours after painting. When pre- treating the wood with a paintable water-repellent preservative (a recommended practice), best  results are achieved if it is applied when temperatures are greater than 10 degree C.
 
Wood was too hot when it was painted or was heated soon after painting
 
Do not paint when the temperature is greater than 45 degree C.
To prevent temperature blisters,avoid painting surfaces that will soon be heated. The best procedure is to “follow the sun around the house.” The east side of the building should be painted late in the morning, the south side in the middle of the afternoon, the west side late in the afternoon. The
north side can be painted at any time during the day. However, at least 2 hours are needed for the fresh paint to dry before weather conditions cool to the point where dew forms. If blistering on the wood surface does occur, allow the paint to dry for a few days, scrape off the blisters, smooth the
edges with sandpaper, and paint the area.
 
The weather was too humid when the surface was painted
 
When water-based paints cure, the water should evaporate as fast or faster than the solvents. After the water has evaporated, the paint will shrink to nearly its final shape. As the solvents evaporate, the solvents may evaporate first, causing the paint to cure while still in a water-filled state. You cannot recover from this type of disaster. Oil-based paints will also fail if conditions are too humid.
 
Humidity in the house was too high during the heating season
 
A high level of humidity inside the house is probably the cause if paint failure occurs on the outside walls of the bathroom or kitchen, and it can be even more pronounced on the outside of an up per floor. In multistory buildings, there is a chimney effect. Warm, moist air is trying to vent upstairs, and eventually this moisture travels out through the siding. Paint failure may be more noticeable near electrical outlets or other breaks in the vapor barrier. Drier air enters through the house cracks on the main level; there- fore, paint failure caused by high humidity is usually not a problem
on the main level. Condensation on the windows also indicates excessive humidity in the house.
Turning down your humidifier or turning on a bathroom exhaust fan will help lower the humidity level inside the house. An energy efficient, but somewhat expensive solution to high levels of humidity is installing an air-to-air heat ex- changer. Here, warm moist air gives its heat to the incoming fresh, dry air.
 
Wood was installed directly over foam or foil-faced insulation board
 
Water can travel in behind the siding of the house through various routes, but has to travel out through the wood, pushing the paint off. Even if the paint remains on the surface, this moisture can cause other problems. Large overhangs, proper caulking, and a 36 cm ground clearance may decrease the chance of water getting in behind the siding. Additional suggestions to prevent paint failure in this situation include the following:
Driving small wedges under every sixth row of siding may permit water to escape and reduce the moisture problem. However, wind-driven rain may also use this as an access and aggravate the situation.
– Back priming (painting the back of the siding before installation) may help reduce or prevent paint failure.
– Install roofing paper beneath the siding. Note: The best solution is to attach furring strips to the studs through the insulation board, making air spaces behind the siding. Furring strips also make a nice home for bugs, if you do not screen the bottom. A new spacer type webbing called “cedar breather” is sometimes used under wood shingles and may have merit for use under siding.
 
House has no interior vapor barrier
 
The absence of an interior vapor barrier is related to the problems of high levels of humidity inside the house during the heating sea- son and wood that was installed directly over foam or foil-faced insulation board. Driving wedges (previously noted) under the sid- ing may be the easiest solution.
Applying certain interior vapor- retarding paints and installing electrical outlet gaskets may also be effective, especially on the up- per floor of a multistory house.
 
Wood siding is dirty
 
If the siding is dirty, the surface of the siding should be power washed or cleaned with detergent and a stiff bristle or brass brush and rinsed well. Never use steel or iron, which causes iron stain and may glaze the surface.
 
Wood has mill glaze
 
Mill glaze can be caused by several factors. For example, if during planing to make smooth wood, the planer blades were dull, running too fast, or pressing too hard on the wood surface, the surface of the wood can become hard- ened or resins may be drawn to the surface causing a glaze.
Whatever the cause, the surface appears to be case hardened. If a drop of water beads up on the wood surface, but does not on a lightly sanded surface, you may have what is commonly called a mill glaze. If you have mill glaze, the smooth surface must be lightly sanded or power washed to remove the hardened surface. Oddly enough, controlled wetting of new siding with a garden hose may promote better adhesion to the re-dried wood. The water re- leases the stresses in the wood.
You can also create a type of mill glaze by sand blasting or using a wire wheel on the wood surface. Mill glaze is not a problem on rough-sawn siding.
 
Brown stains appear on the surface of the paint
 
Paint does not have to fall off to fail. Moisture traveling through wood pulls water-based extractives through the paint, leaving brown stains on the surface of the paint. If the wood is kept dry, the water-based extractives in the wood will not bleed through paint. Keeping all moisture out may be difficult. Oil-based primers usually block extractive stains better than latex primers and may be a better choice on redwood and cedar; however, oil paints can increase mildew. Compared with oil-based primers, latex primers produce a more flexible paint film with better durability and can be used when extractive staining is not a problem. Improved stain